0
Guides

Why a Shelly relay keeps resetting when it drives a contactor, and how a snubber fixes it

October 5, 20265 min read

Many electricians wire a Shelly relay to a contactor that runs an air conditioner, do everything by the book, and a few weeks later get a call from the customer: the device keeps dropping off the network, resets itself and eventually stops working. In this article, OZZI, the official Shelly distributor in Israel, explains what actually happens inside the panel, and why a small, inexpensive part called a snubber is an essential part of every smart switch installation that drives an inductive load in a smart home.

1. The familiar scenario from the field

An air conditioner, pump or motor switched through a contactor, with a Shelly relay switching the contactor coil.

The common assumption is that if the heavy load doesn’t pass through the relay, the relay is protected. The air conditioner’s operating current does flow through the contactor, and the relay “only” switches the coil on and off. In practice, the coil is exactly where the problem comes from.

The symptoms usually show up in this order: Wi-Fi dropouts at the moment of switching on or off, repeated reboots, settings being wiped, a relay contact that sticks or fails to close, and finally a device that no longer works. The more contactors in the same panel and the more switching cycles per day, the faster this happens.

2. What happens the moment the circuit opens

A contactor coil is an inductor, and an inductor resists any sudden change in current.

While the coil is energized, energy is stored in its magnetic field. The moment the relay contact opens, the current is cut off within microseconds and the magnetic field collapses. According to V = L·di/dt, such a sharp change in current produces a reverse induced voltage (back EMF) that can reach hundreds or even thousands of volts for a very short time.

That energy has to go somewhere. When it has no controlled path, it finds three unwanted ones:

1

Arcing across the relay contacts. The high voltage strikes an arc between the opening contacts. Every arc burns away a little contact material, leaves carbon behind and pits the surface. After a few hundred cycles the contact starts to weld or fails to close properly.

2

Electromagnetic interference (EMI) to the processor. The arc and the spikes generate high-frequency noise that travels along the wires and through the air. Inside a Shelly relay sit a microcontroller and a Wi-Fi module that run at very low voltages. Noise like this causes resets, network dropouts and, when it happens repeatedly, corrupted memory and wiped settings.

3

Stress on the internal power supply. The spike also travels back to the device’s own supply line. The protection components in the small power supply inside the relay absorb it again and again, wear out and eventually fail.

That’s the mechanism: the problem isn’t the current the relay carries, but the energy the coil releases the moment the relay disconnects it.

3. What speeds up the damage

Coil size, the number of loads in the panel and how often it switches.

The bigger the contactor, the stronger its coil and the more energy it stores. When there are several contactors or inductive loads in the same panel, each relay is exposed not only to the spike from its own load, but also to noise from the other loads running next to it in the wiring and the busbar.

Switching frequency matters too: schedules, temperature-based automations and managing electricity use by tariff all add on and off cycles throughout the day. Every cycle is another arc and another spike. That’s how a device that should last for years gets damaged within a short time.

4. What the snubber does

An RC network: a resistor and a capacitor in series, connected in parallel with the load.

The snubber gives the coil’s energy a controlled path. The moment the circuit opens, the capacitor absorbs the current the coil keeps pushing, which stops the voltage from spiking. The resistor dissipates the energy as heat and damps oscillation. The result is a voltage that rises slowly and stays low, instead of a sharp spike.

In practice, that means no arcing on the relay contacts, no noise rebooting the processor and no wear on the internal power supply. The same device that used to reset every few days now runs reliably.

5. How to connect it

4

Switch off the power at the panel before you start.

5

Connect the snubber in parallel with the contactor coil, across terminals A1 and A2, as close to the coil as possible.

6

Install a separate snubber for each inductive load. In a panel with several contactors, each contactor gets its own snubber.

7

Restore power and run a few on and off cycles from the Shelly Smart Control app to make sure the device stays connected and stable.

Recommended

The same principle applies when a Shelly relay directly switches fans, range hoods, refrigerators, air conditioners, washing machines, dryers, transformers and LED lights.

RC snubber for use with Shelly relays

Snubber for use with Shelly relays

A resistor and capacitor in series in a compact 27×8×17 mm housing. Connect it in parallel with the load, as close to the load as possible.

Go to the product page on the OZZI website →

Installing smart switches and smart energy meters correctly is the foundation of a stable smart home and of managing and reducing electricity use for years to come. A snubber on every inductive load saves repeat service calls and replacement devices. This article was prepared by OZZI, the official distributor of Shelly smart home products in Israel.

Need help with installation or setup?
Ask us, book an electrician who knows Shelly devices, or plan your home for free.

More articles

All articles →
November 17, 2026מתכנן בית חכם: איך מתכננים את הבית ומקבלים הצעות מחיר מחשמלאיםאיך משתמשים במתכנן הבית החכם של OZZI בכ-2 דקות, ואיך מקבלים הצעות מחיר מחשמלאים מוסמכים להתקנה. מדריך עם צילומי מסך, בחינם ובלי התחייבות.Read →November 11, 2026Shelly and Matter: which devices support it and how to connect to each systemWhat Matter is and how to connect Shelly devices: which models support it (Gen4 and Gen3), enabling it, where to find the code, connecting to Apple…Read →November 11, 2026Connecting Shelly to Home Assistant: built-in integration, Matter or ZigbeeHow to connect Shelly devices to Home Assistant: the local built-in integration, Matter, or Zigbee through ZHA and Zigbee2MQTT on Gen4 devices. A comparison, which route…Read →