0
Guides

Setting up a Shelly device: shutters, lighting and calibration

November 2, 20266 min read

Your device is connected to the app? Now set it up for what it controls: a shutter, lights or a water heater. This guide covers the key settings, what to do after a power outage and how to fix common problems. It applies to Shelly Gen3 and Gen4 devices: 2PM, 1PM, 1, Mini and Pro. On older devices (Plus, 2.5), the screen names may be slightly different.

Installing the device in the wall or in the electrical panel must be done by a licensed electrician. This guide starts after the device has been installed and connected to the app.

1. Before you start

Three quick checks.

1

The device appears on the home screen, inside a room. If it isn’t connected yet, start with adding a new Shelly device to the app.

2

Update the firmware if an update icon appears next to the device. Some settings only exist in recent versions. See the firmware update guide.

3

Check what’s connected: a shutter or lights / an appliance, and what’s on the wall: a switch (stays in the position you set) or a push button (spring-loaded and returns to place, like a doorbell).

2. Setting up a shutter

For the Shelly 2PM (Gen3 and Gen4) and the Pro Dual Cover. Follow the steps in order so the motor isn’t damaged.

Note

Only one shutter per device (or per channel on the Pro Dual Cover). Never connect two motors in parallel to the same output. The wiring itself is shown in the 2PM Gen4 shutter wiring diagram.

4

On the home screen, open the device and tap the settings icon (the gear) at the bottom of the icon bar on the side of the screen.

5

Choose “Device Profile” → “Cover” and save. The device restarts, and after a few seconds the open, stop and close buttons appear.

6

Open “Input/Output Settings” and choose the type of wall switch: “Switch” or “Button”. Then save.

7

Check the directions from the app: tap “Open”. If the shutter goes down instead of up, tick “Reverse Directions” and save.

8

Check the directions from the wall switch. If pressing up lowers the shutter, tick “Swap Inputs” and save.

9

Calibrate: “Position Calibration” → “Start Calibration”. The shutter goes all the way up and down twice and measures its travel times. Don’t touch the shutter or the switch until the calibration is finished. From now on you can open it by percentage, for example 30% for shade at midday.

Calibration failing?

Calibration relies on the motor stopping at each end. If the shutter doesn’t stop by itself at the top and bottom (the limit switches aren’t set), calibration will fail. In that case the electrician or shutter installer needs to adjust the motor before calibrating.

3. Setting up lighting or an appliance

For the 1PM, 1, Mini, 1L/2L, and a 2PM connected to two lights.

10

On the 2PM only: “Device Profile” → “Switch” (not Cover), and save. On the other devices, skip this step.

11

Open “Input/Output Settings”. Under “Select Input Button/Switch Mode”, choose “Switch” or “Button”, depending on what’s on the wall.

12

With a regular switch, under “Set Relay Type” choose “Edge” (“Flip on every change”). That way every press toggles the state, even after you’ve turned it on from the app, so you never need to press twice. The full explanation, with screenshots, is in the guide to connecting to the app. On a 2PM with two lights, repeat this for each channel.

Switch doesn’t do anything?

There’s a mode in which the wall switch doesn’t operate the relay directly, but only sends a command to a scene in the app. It’s useful for advanced setups, for example when one switch turns off the whole house. If the switch “does nothing”, check that this mode wasn’t selected by mistake.

4. What happens after a power outage

For each device, you set what it does when the power comes back.

In the device settings, choose the state after power is restored: off, on or restore last state. Our recommendations:

  • Lighting: off, or restore last state. Otherwise a power outage in the middle of the night turns on the whole house.
  • Water heater, oven and radiator: off. That way they don’t switch on by themselves after an outage when nobody is home, and the schedule will turn them on at the right time.
  • Shutters: the shutter stays where it is. After a long outage, check that the percentages are still accurate, and if not, calibrate again.

Important for schedules

Schedules are stored on the device itself, but after a power outage it needs the internet to know what time it is. If the router stays off, schedules won’t run until the connection is back. A small UPS for the router solves this. See the home network guide.

5. Schedules and scenes

Once the device is set up, this is the part that makes it smart.

  • Schedule: on and off at a set time, by day of the week or relative to sunrise and sunset. The schedule is stored on the device and works even without internet. Ideal for the water heater, outdoor lighting and shutters, and also as a smart Shabbat timer for any switch.
  • Scene: several actions together, for example “Good night”, which turns off all the lights and lowers the shutters. Scenes run in the Shelly cloud, so they need the internet.
  • Consumption and cost: on devices that measure power (PM), you can set a tariff and see the cost in shekels. See setting electricity tariffs.

6. Common problems

  • The shutter moves the wrong way: use “Reverse Directions” when the problem is in the app, and “Swap Inputs” when it’s at the wall switch (step 2).
  • The percentages are off: calibrate again. This is also needed after replacing the motor or readjusting its limits.
  • You have to press the switch twice: choose “Edge” (step 3).
  • The device is “unavailable” or responds slowly: almost always a Wi-Fi problem. See the home network guide.
  • Nothing helps: you can reset the device and set it up again using the reset and reconnect guide.

Need help with the installation? Book an electrician who knows Shelly. This guide was prepared by OZZI, the official distributor of Shelly smart home products in Israel.

Need help with installation or setup?
Ask us, book an electrician who knows Shelly devices, or plan your home for free.

More articles

All articles →
November 17, 2026מתכנן בית חכם: איך מתכננים את הבית ומקבלים הצעות מחיר מחשמלאיםאיך משתמשים במתכנן הבית החכם של OZZI בכ-2 דקות, ואיך מקבלים הצעות מחיר מחשמלאים מוסמכים להתקנה. מדריך עם צילומי מסך, בחינם ובלי התחייבות.Read →November 11, 2026Shelly and Matter: which devices support it and how to connect to each systemWhat Matter is and how to connect Shelly devices: which models support it (Gen4 and Gen3), enabling it, where to find the code, connecting to Apple…Read →November 11, 2026Connecting Shelly to Home Assistant: built-in integration, Matter or ZigbeeHow to connect Shelly devices to Home Assistant: the local built-in integration, Matter, or Zigbee through ZHA and Zigbee2MQTT on Gen4 devices. A comparison, which route…Read →